1 - 10 out of 46Page size: 10
  1. 2023

  2. Correction to: Technological Shells in Rolling Processes of Thin Sheets from Hard-to-Deform Materials

    Salikhyanov, D., Kamantsev, I. & Michurov, N., 1 Nov 2023, In: Journal of Materials Engineering and Performance. 32, 22, p. 10103-10103 1 p.

    Research output: Contribution to journal › Article › peer-review

  3. Joining of dissimilar aluminum alloys AA5154 and AA2024 by cold roll bonding

    Salikhyanov, D. & Michurov, N., 1 Nov 2023, In: International Journal of Advanced Manufacturing Technology. 129, 1-2, p. 255-277 23 p.

    Research output: Contribution to journal › Article › peer-review

  4. Technological Shells in Rolling Processes of Thin Sheets from Hard-to-Deform Materials

    Salikhyanov, D., Kamantsev, I. & Michurov, N., 1 Nov 2023, In: Journal of Materials Engineering and Performance. 32, 22, p. 10085-10102 18 p.

    Research output: Contribution to journal › Article › peer-review

  5. КОНЦЕПЦИЯ МИКРОМОДЕЛИРОВАНИЯ ПРОЦЕССА СОЕДИНЕНИЯ РАЗНОРОДНЫХ МАТЕРИАЛОВ ПЛАСТИЧЕСКОЙ ДЕФОРМАЦИЕЙ

    Салихянов, Д. Р. & Мичуров, Н. С., 15 Sept 2023, In: Обработка металлов (технология, оборудование, инструменты). 25, 3, p. 36-49 14 p.

    Research output: Contribution to journal › Article › peer-review

  6. МОДЕЛИРОВАНИЕ ПРОЦЕССА ПРОКАТКИ СЛОИСТОГО КОМПОЗИТА АМГ3/Д16/АМГ3

    Салихянов, Д. Р. & Мичуров, Н. С., 15 Sept 2023, In: Обработка металлов (технология, оборудование, инструменты). 25, 3, p. 6-18 13 p.

    Research output: Contribution to journal › Article › peer-review

  7. Исследование напряженно-деформированного состояния на границе между материалами при прокатке слоистого композита

    Салихянов, Д. Р., 2023, In: Черные металлы. 9, p. 34-39 6 p.

    Research output: Contribution to journal › Article › peer-review

  8. 2022

  9. Flow behavior and microstructure evolution of Ti-6Al-4V titanium alloy produced by selective laser melting compared to wrought

    Salikhyanov, D., Veselova, V. & Volkov, V., Mar 2022, In: International Journal of Advanced Manufacturing Technology. 119, 1-2, p. 953-967 15 p.

    Research output: Contribution to journal › Article › peer-review

  10. 2020

  11. Rheological Properties and Microstructure of AlSi10Mg Aluminum Alloy produced by Selective Laser Melting

    Salikhyanov, D. R., Gladkovskii, S. V., Avraamov, Y. A., Volkov, V. P. & Veselova, V. E., 3 Jan 2020, In: IOP Conference Series: Materials Science and Engineering. 709, 3, 033113.

    Research output: Contribution to journal › Conference article › peer-review

  12. Development and investigation of the forging method of long-length blanks with mutual displacement of anvils

    Volkov, V. P., Salikhyanov, D. R. & Kamantsev, I. S., 1 Jan 2020, In: Journal of Chemical Technology and Metallurgy. 55, 3, p. 571-579 9 p.

    Research output: Contribution to journal › Article › peer-review

  13. Rheological properties and microstructure of PH1 stainless steel produced by selective laser melting

    Gladkovsky, S. V., Salikhyanov, D. R., Volkov, V. P., Avraamov, Y. A. & Veselova, V. E., 1 Jan 2020, Materials Science and Metallurgical Technology II. Radionov, A. A. (ed.). Trans Tech Publications Ltd., p. 811-815 5 p. (Materials Science Forum; vol. 989 MSF).

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

Previous 1 2 3 4 5 Next

ID: 114424