21 - 30 out of 81Page size: 10
  1. 2017

  2. РАСЧЕТ СИЛОВЫХ ПАРАМЕТРОВ ПРИ ВЫСАДКЕ КОНЦОВ ТРУБ НЕФТЯНОГО СОРТАМЕНТА МЕТОДОМ ВЕРХНЕЙ ОЦЕНКИ

    Ерпалов, М. В., Дыя, Х. & Богатов, А. А., 2017, In: Металлург. 3, p. 19-22 4 p.

    Research output: Contribution to journal › Article › peer-review

  3. Intensification of Tube Plugging Based on Simulation Results

    Bogatov, A. A., Pavlov, D. A. & Pavlova, E. A., Jan 2017, In: Metallurgist. 60, 9-10, p. 1016-1021 6 p.

    Research output: Contribution to journal › Article › peer-review

  4. Development of Bonding Mechanisms for Different Materials During Forming

    Bogatov, A. A. & Salikhyanov, D. R., Mar 2017, In: Metallurgist. 60, 11-12, p. 1175-1179 5 p.

    Research output: Contribution to journal › Article › peer-review

  5. Technique of determining the parameters of rapid strengthening of an aluminum alloy during hot rolling

    Loginov, Y. N. & Golovnin, M. A., 1 Mar 2017, In: Russian Metallurgy (Metally). 2017, 3, p. 188-192 5 p.

    Research output: Contribution to journal › Article › peer-review

  6. Simulation of Rotary Piercing Process

    Bogatov, A. A., Nukhov, D. S. & Toporov, V. A., May 2017, In: Metallurgist. 61, 1-2, p. 101-105 5 p.

    Research output: Contribution to journal › Article › peer-review

  7. 2018

  8. ИССЛЕДОВАНИЕ ВЛИЯНИЯ КАЛИБРОВКИ ОПРАВКИ НА РАЗНОСТЕННОСТЬ ПРИ ПРОДОЛЬНОЙ ПРОКАТКЕ ТРУБ

    Павлов, Д. А., Богатов, А. А. & Павлова, Е. А., 2018, In: Черная металлургия. Бюллетень научно-технической и экономической информации. 7(1423), p. 65-70 6 p.

    Research output: Contribution to journal › Article › peer-review

  9. РАЗРАБОТКА И ВНЕДРЕНИЕ ТЕХНОЛОГИИ И, ОБОРУДОВАНИЯ ДЛЯ МНОГОКРАТНОГО ВОЛОЧЕНИЯ ТОНКОСТЕННЫХ ТРУБ ИЗ МЕДНЫХ СПЛАВОВ НА ДЛИННОЙ ПОДВИЖНОЙ ОПРАВКЕ БЕЗ ПРОМЕЖУТОЧНОЙ ТЕРМООБРАБОТКИ

    Акчурин, Р. З., Богатов, А. А., Салихянов, Д. Р. & Овчинников, А. С., 2018, In: Металлург. 10, p. 61-66 6 p.

    Research output: Contribution to journal › Article › peer-review

  10. A study of the influence of the manufacturing process parameters on the distribution of residual stresses in pipe walls during sink drawing

    Shimov, G., Shimov, V. & Zavalin, A., 1 Jan 2018, Materials Engineering and Technologies for Production and Processing IV. Radionov, A. (ed.). Trans Tech Publications Ltd., p. 542-546 5 p. (Solid State Phenomena; vol. 284 SSP).

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

  11. Development and research of the method of severe alternating deformation in the process of rolling of thick steel sheets and plates made of non-ferrous alloys

    Bogatov, A. & Nukhov, D., 1 Jan 2018, Materials Engineering and Technologies for Production and Processing IV. Radionov, A. (ed.). Trans Tech Publications Ltd., p. 265-269 5 p. (Solid State Phenomena; vol. 284 SSP).

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

  12. Fem simulation of copper busbar pressing on the continuous extrusion line"conform"

    Shimov, G., Bogatov, A. & Kovin, D., 1 Jan 2018, Materials Engineering and Technologies for Production and Processing IV. Radionov, A. (ed.). Trans Tech Publications Ltd., p. 547-551 5 p. (Solid State Phenomena; vol. 284 SSP).

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

Previous 1 2 3 4 5 6 7 8 9 Next

ID: 1295263